ASTM D2369 FREE DOWNLOAD

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phone , fax , or service astm. Other procedures may be substituted with mutual agreement between the producer and the user. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Link to Active This link will always route to the current Active version of the standard. Other procedures may be substituted with mutual agreement between the producer and the user. Weigh to the nearest 0. NOTE 4—Be sure the shelves are level and dampers are open.

Uploader:	Mom
Date Added:	15 November 2015
File Size:	32.96 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	81613
Price:	Free* [*Free Regsitration Required]

NOTE 3—If unusual decomposition or degradation of the specimen occurs during heating, the actual time and temperature used to cure the coating in practice may be substituted for the time and temperature speci?

These coatings single package, heat cured are commonly applied in factories to automobiles, metal containers,? This information is useful to the paint producer and user and to environmental interests for determining the volatiles emitted by coatings.

Your comments will receive careful consideration at a meeting of qstm responsible technical committee, which you may attend. This information is useful to the paint producer and user and to environmental interests for determining the volatiles emitted by coatings. Your comments are invited either for revision of this standard or for additional standards and should be aatm to ASTM International Headquarters.

ASTM D - 10 Standard Test Method for Volatile Content of Coatings

The coatings used in these round-robin studies represented aastm, air-dried oxidizing, heat-cured baking systems, and also included multicomponent paint systems. Link to Active This link will always route to the current Active version of the standard. Committee D01 has run round-robin studies on volatiles of multicomponent paint systems. The only change in procedure is to premix the weighed components in the correct proportions and d2396 the specimens to stand at room temperature for 1 h prior to placing them into the oven.

Other procedures may be substituted with mutual agreement between the producer and the user. The within-laboratory coefficient of variation was found to be 0. Obtain a freshly stirred sample for each test run. Mix thoroughly before taking specimens for individual tests. No other units of measurement are s2369 in this standard. NOTE 10—Use disposable no talc rubber gloves or polyethylene to handle the syringe.

After dispersing, allow to stand for 1 h at room temperature induction period before placing the dishes into the oven.

VOC Testing – ASTM D2369 & EPA Method 24

A number in parentheses indicates the year of last reapproval. Summary of Test Method 3.

It is the responsibility of the user of this standard to establish appropriate asrm and health practices and determine the applicability of regulatory limitations prior to use. Work Item s - proposed revisions of this standard.

The weight percent solids content nonvolatile matter may be determined by difference. NOTE 11—If the specimen cannot be dispersed in the solvents listed 6. Wipe the outer surface of the syringe to remove excess material and cap the axtm.

In addition to other precautions, provide adequate ventilation, consistent with accepted laboratory practice, to prevent solvent vapors from accumulating to a dangerous level.

Remove the syringe from the specimen, pull the plunger tip up 6. D — 03 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Mix the components together immediately, weigh the appropriate sample size from the table in 7. Note 2—Committee D01 has run round-robin studies on volatiles of multicomponent paint systems. EPA Reference Method The only change in procedure is to premix the weighed components in the correct proportions and allow the satm to stand at room temperature for 1 h prior to placing them into the oven. Two results, each the mean of duplicate determinations obtained by operators in different laboratories, should be considered suspect if they vary by more than 5.

Other procedures may be substituted with mutual agreement between the producer and the user.

ASTM D - 10()e1 Standard Test Method for Volatile Content of Coatings

NOTE 8—Draw the specimen into the syringe. EPA Reference Method 24 speci?

NOTE 6—For waterborne paint systems it is recommended that they be stirred by hand.